Richmond Hill Attic Insulation & Air Sealing installs spray foam attic insulation in Richmond Hill, and our certified technicians measure the finished result instead of estimating from depth alone. Spray foam expands into every crack, seam and penetration as it goes on, sealing air leaks and insulating in one step. That makes it the right call for tight, awkward attics, roofs crowded with framing and wiring, or homes where no amount of blown-in insulation has stopped the drafts.
What goes into every spray foam attic we complete:
Most of our spray foam attic projects in Richmond Hill run $4,500 to $10,000 for a full roof deck on a typical 1,000 to 1,400 sq ft attic. Flash-and-fill jobs usually come in between $3,000 and $6,000. Every job starts with a free inspection and a written quote from us.
Tired of drafts that keep coming back after every top-up? Call us, and we’ll show you whether spray foam is the right fit for your attic.
Richmond Hill Attic Insulation & Air Sealing runs a blower door test on every home before any work begins.
The fan depressurizes the house so our technicians can measure how leaky it really is and where the air escapes.
The test runs again after installation, and both results are recorded for you to keep.
Since 2005, our crews have worked through older homes, non-standard attic layouts and tricky ventilation setups.
That adds up to 500+ attic projects across Richmond Hill and the GTA, with 150+ completed in 2026 alone.
A 97% client satisfaction rate shows the work holds up long after the crew leaves.
Every install follows Ontario Building Code standards, with R-values suited to freeze-thaw winters and summer heatwaves.
Before we start, you receive a written scope, confirmed material specs and a clear timeline.
A written warranty then covers both the materials and our workmanship.
A 4-person crew finishes most attics in 4 to 8 hours, so your day stays close to normal.
Hoses feed straight into the attic to keep dust out of your living space, and cleanup and haul-away are included.
The balance is only due after a senior supervisor walks through the finished attic with you.
We’ll call you back within 2 business days to book your free inspection.



Two rounds of blown-in top-ups hadn’t stopped the drafts in this 2000s two-storey near Bathurst and Elgin Mills. Up in the 1,250 sq ft attic, daylight showed through the roof deck seams, and condensation had stained the OSB near the eaves.
Our Richmond Hill Attic Insulation & Air Sealing crew Our crew sprayed Walltite closed-cell foam about 5.5 inches deep across the roof deck, sealed off the box vents and soffits, and finished the exposed foam with DC315 coating.
The follow-up blower door test showed air leakage cut by nearly half, and the upstairs drafts are gone.
Turnaround Time: 2 days
Final Price: $9,200

Closed-Cell Attic Spray Foam
Closed-cell spray foam creates a dense insulation layer for selected roofline sections, rim areas, narrow framing cavities, and attic locations where limited depth requires higher thermal resistance in a compact application. The material expands after installation and bonds to compatible substrates, helping seal irregular gaps while insulating areas that are difficult to treat with loose-fill or batt materials.
Richmond Hill Attic Insulation & Air Sealing evaluates the roof sheathing, framing, substrate condition, moisture exposure, ventilation strategy, and required clearances before recommending closed-cell foam. Wet surfaces, active leaks, contaminated substrates, and inaccessible cavities must be corrected or prepared before application. The installation also protects electrical components, ducts, fixtures, and service areas from overspray.
Open-Cell Roofline Spray Foam
Open-cell spray foam expands into larger voids and irregular roofline cavities, making it suitable for selected attic assemblies where the framing depth can accommodate a thicker insulation layer. The foam conforms to joints, transitions, and framing contours that may be difficult to seal with rigid boards or batt insulation. Proper installation creates a continuous air-control layer across the designated roofline area.
Technicians inspect roof geometry, sheathing, framing depth, soffit pathways, ridge ventilation, ducts, wiring, and mechanical equipment before selecting open-cell foam. Moisture problems and roof leaks must be corrected before spraying, and ventilation channels must remain open where the roof assembly requires them. Richmond Hill Attic Insulation & Air Sealing manages application boundaries carefully to preserve service access and prevent foam from covering components that require inspection.


Spray foam can seal selected openings around plumbing stacks, electrical wiring, duct transitions, top plates, framing joints, and other attic bypasses. These gaps may allow conditioned air to escape even when the surrounding attic contains adequate insulation. Technicians apply foam to compatible surfaces after checking the opening size, substrate condition, temperature exposure, and proximity to heat-producing components.
Recessed lights, chimneys, flues, and electrical systems require separate clearance and protection checks before foam is installed nearby. Some areas may need fire-rated materials, rigid barriers, equipment repairs, or exclusion from the spray area rather than standard foam application. Richmond Hill Attic Insulation & Air Sealing coordinates penetration sealing with existing building systems and identifies repair requirements before installation.
Knee walls, dormers, vaulted transitions, and sloped attic sections often contain irregular cavities where batt insulation can leave compression gaps, open edges, and thermal bridges. Spray foam can conform to selected framing spaces and seal joints along the attic-side wall or roofline when the assembly is accessible and suitable for application. This work targets comfort problems caused by thin insulation, air leakage, and difficult framing geometry.
Before spraying, Richmond Hill Attic Insulation & Air Sealing checks the knee-wall sheathing, framing, adjacent living-space finishes, roof ventilation, wiring, ducts, and access route. The material selection depends on cavity depth, moisture conditions, roof design, and required service clearances. Restricted areas may require localized foam placement, surface preparation, or a combination of spray foam and another insulation material.

01
We begin by examining the attic structure, roof sheathing, framing cavities, existing insulation, moisture indicators, ventilation openings, wiring, ducts, fixtures, and access conditions. Technicians determine whether the proposed application belongs at the attic floor, roofline, knee wall, rim area, or a combination of locations. The substrate must be dry, stable, accessible, and free from conditions that could compromise adhesion or conceal damage.
Findings from the evaluation determine whether spray foam is suitable or whether the scope must include leak repair, insulation removal, surface preparation, ventilation changes, or electrical corrections. A roof assembly with active moisture or inaccessible cavities cannot be treated the same way as a dry, open framing bay. This assessment creates the technical basis for material selection and installation planning.
02
Technicians prepare compatible substrates by clearing loose debris, moving or removing conflicting insulation, and exposing the areas that require continuous coverage. We protect windows, wiring, ducts, fixtures, ventilation openings, finished surfaces, and serviceable equipment from overspray. Heat-producing components receive clearance checks, and areas requiring barriers or separate repairs are identified before foam application.
The preparation stage can change the installation method when technicians find damp sheathing, deteriorated wood, pest contamination, or unsafe electrical conditions. Richmond Hill Attic Insulation & Air Sealing keeps these findings within the decision process instead of spraying over unstable surfaces. Once the work area is dry, clean, protected, and accessible, the foam type and application sequence can proceed.
03
We then apply the selected open-cell or closed-cell foam to the prepared roofline, framing cavities, penetrations, or targeted attic sections. Application thickness, expansion, substrate contact, ventilation clearance, and edge coverage must remain controlled throughout the installation. The work proceeds in planned areas so foam does not obstruct soffit airflow, cover electrical junctions, or interfere with ducts and service components.
Changing cavity conditions can require localized hand detailing, additional preparation, or a revised application boundary. We monitor the foam’s expansion and adhesion as the material cures and correct incomplete edges or visible voids where access allows. The installed foam must remain connected across the intended air-control layer without covering systems that require inspection or maintenance.
04
After curing and application, we review accessible foam surfaces for gaps, pull-away, thin sections, overspray, blocked ventilation channels, and compromised service access. Technicians inspect transitions at framing joints, penetrations, roofline changes, knee walls, and other locations included in the work scope. Any area excluded because of safety, access, or substrate limitations is identified for a separate decision.
The final review determines whether additional foam detailing, surface correction, ventilation work, or another insulation material is necessary. We also confirm that equipment, ducts, wiring, fixtures, and attic access remain serviceable. This stage gives Richmond Hill property owners a practical record of what was treated and what conditions may require future work.
Spray foam attic insulation typically costs $1.50 to $4.50 per square foot for the insulation installation portion, depending on the foam type, application location, required insulation level, access, and preparation work. A 1,000-square-foot attic commonly costs $1,500 to $4,500, while larger or more complex projects may reach $6,000 or more when old insulation removal, air sealing, ventilation work, surface preparation, or disposal is required. Richmond Hill Attic Insulation & Air Sealing evaluates the roof assembly and defines the foam, preparation, repair, and access scope before pricing the complete project.
Spray foam attic insulation typically takes a half day to 1 full day for application when the attic is dry, accessible, and ready for spraying. The initial inspection generally takes 30 to 45 minutes, the written assessment and quote may take 24 to 48 hours, and material selection or ventilation planning can require 1 to 3 days. Surface preparation, insulation removal, ventilation protection, or repairs may add a half day to 1 full day before application. Richmond Hill Attic Insulation & Air Sealing sequences preparation, spraying, curing considerations, and coverage review according to the attic’s condition.
Yes, spray foam attic insulation can be suitable for an existing attic when the roof assembly, substrate, moisture condition, ventilation design, access, and surrounding systems support the planned application. Existing insulation may require selective movement or removal so technicians can inspect and prepare the spray area. Wet sheathing, active leaks, contaminated surfaces, unsafe wiring, blocked ventilation, and clearance problems must be corrected before spraying. Richmond Hill Attic Insulation & Air Sealing evaluates these factors and determines whether foam belongs at the attic floor, roofline, knee wall, rim area, or only at selected penetrations.
Existing attic insulation should be removed before spray foam is installed when it covers the roofline, blocks access to the application surface, contains moisture or contamination, or prevents inspection of the substrate. Dry and stable insulation may remain in areas outside the spray-foam boundary when it does not interfere with preparation, ventilation, or service access. Richmond Hill Attic Insulation & Air Sealing checks the material condition, roof sheathing, framing, pest evidence, and intended application area before deciding on full removal, selective removal, or retention. The decision affects preparation time, disposal, material placement, and the final scope.
No, spray foam cannot be applied around wiring, ducts, recessed lights, and chimneys without evaluating the component type, heat exposure, clearance, accessibility, and required protective method. Richmond Hill Attic Insulation & Air Sealing protects serviceable systems and identifies unsafe or incompatible conditions before spraying. This component-by-component review helps prevent overspray, blocked ventilation, concealed defects, and unsafe contact with heat-producing equipment.