Richmond Hill Attic Insulation & Air Sealing has been sealing and fire-stopping chimney chases in Richmond Hill homes since 2005. The chase is the gap around a chimney or flue where it passes through the attic floor. In many houses, we find it was framed and then left wide open, which lets warm air escape all winter and gives fire a clear path upward. We close each chase with non-combustible materials that keep the clearance a hot flue needs, so your attic gets tighter without getting riskier.
What goes into every chase we seal:
Most of our chimney chase sealing jobs in Richmond Hill run $350 to $900 per chase, depending on size and flue type. Homes with multiple flues or soiled insulation can reach $1,500. Every job starts with a free inspection and a written quote from us.
Spotted a draft near the fireplace or dark streaks around the chimney insulation? Call us, and we’ll show you exactly what your chase needs.
Richmond Hill Attic Insulation & Air Sealing runs a blower door test on every home before any work begins.
The fan depressurizes the house so our technicians can measure how leaky it really is and where the air escapes.
The test runs again after installation, and both results are recorded for you to keep.
Since 2005, our crews have worked through older homes, non-standard attic layouts and tricky ventilation setups.
That adds up to 500+ attic projects across Richmond Hill and the GTA, with 150+ completed in 2026 alone.
A 97% client satisfaction rate shows the work holds up long after the crew leaves.
Every install follows Ontario Building Code standards, with R-values suited to freeze-thaw winters and summer heatwaves.
Before we start, you receive a written scope, confirmed material specs and a clear timeline.
A written warranty then covers both the materials and our workmanship.
A 4-person crew finishes most attics in 4 to 8 hours, so your day stays close to normal.
Hoses feed straight into the attic to keep dust out of your living space, and cleanup and haul-away are included.
The balance is only due after a senior supervisor walks through the finished attic with you.
We’ll call you back within 2 business days to book your free inspection.



A steep-pitched, 640 sq ft attic in a 1970s two-storey near Mill Pond was losing heat through an open gap around its B-vent flue and through unsealed wiring holes.
Our Richmond Hill Attic Insulation & Air Sealing crew wrapped the flue in a 26-gauge galvanized sheet metal collar, sealed every seam with high-temperature caulk, and packed ROCKWOOL mineral wool around the base. We then sprayed 2 inches of closed-cell foam across the roof deck.
The follow-up blower door test showed leakage down from 7.2 to 3.8 ACH50, and the upstairs rooms stopped running cold.
Turnaround Time: 1 day
Final Price: $6,850

Masonry chimneys often pass through attic floors and roof assemblies with gaps around brick, mortar, flashing, or the framed chase. These openings can create strong air leakage paths and allow attic insulation or debris to collect near the chimney. Sealing the perimeter helps close the ceiling or attic air barrier without bonding materials directly to unstable masonry.
Richmond Hill Attic Insulation & Air Sealing evaluates mortar joints, chase framing, flashing, metal liners, roof sheathing, and the transition between masonry and combustible framing. Our technicians use compatible high-temperature sealants, sheet metal, mineral wool, or noncombustible blocking where the assembly permits. Cracked masonry, active water entry, damaged flashing, or an unsafe flue requires correction before air sealing can proceed.
Factory-built metal chimneys require clearances and fire-stopping at each location where the chimney passes through an attic floor, ceiling, or roof assembly. Missing collars, open framing bays, displaced insulation, and improvised materials can compromise the intended separation around the chimney. The repair must preserve the chimney’s listed configuration and avoid restricting required ventilation or inspection access.
Our technicians inspect the metal flue, support box, attic insulation, framing, firestop components, and chase cap before selecting replacement materials. Richmond Hill Attic Insulation & Air Sealing uses noncombustible materials such as mineral wool, sheet metal, or compatible listed components where appropriate. Damaged factory-built chimney parts or unclear clearance requirements may require manufacturer-specific parts or review by a qualified chimney professional.


A framed chimney chase can contain open stud bays, unsealed top plates, missing blocking, and gaps around pipes or supports. These pathways allow attic air to bypass the intended thermal boundary and can spread drafts through wall or ceiling cavities. Air sealing focuses on the chase boundaries while maintaining the separation required around the flue.
Richmond Hill Attic Insulation & Air Sealing traces the chase from the attic floor to the roof deck and identifies openings at framing joints, drywall, sheathing, and service penetrations. Our technicians install compatible fire-rated sealants, noncombustible blocking, sheet metal, and mineral wool according to the location and heat exposure. The chase must be stable and accessible; deteriorated framing or concealed damage can require additional repair before sealing.
Insulation placed against a chimney or metal flue can create a clearance concern, especially when loose-fill material has shifted or batt insulation has been installed without a proper barrier. Heat discoloration, brittle insulation, soot, odor, or damaged framing should not be covered. Correcting the surrounding insulation requires careful separation from the hot surface and the installation of suitable noncombustible protection.
Our technicians identify insulation type, depth, movement, moisture, charring, and contact with the chimney assembly before removing or repositioning material. Richmond Hill Attic Insulation & Air Sealing installs or repairs blocking and fire-stopping, then places insulation only where the chimney configuration permits. Evidence of overheating, smoke damage, or flue deterioration changes the work from insulation correction to a broader safety evaluation.

01
The process begins by determining whether the home has a masonry chimney, factory-built metal chimney, or another venting assembly. They inspect the flue, liner, support box, chase framing, flashing, cap, collars, insulation, and visible clearance zones from the attic. Correct identification matters because masonry and factory-built systems use different components, materials, and installation requirements.
Findings such as damaged metal, missing firestop parts, cracked mortar, active leaks, or uncertain clearance affect whether attic sealing can begin. Richmond Hill Attic Insulation & Air Sealing separates air leakage findings from chimney-system defects and identifies conditions requiring another qualified professional. The assembly type and access route guide the next preparation stage.
02
Loose insulation and debris are moved away from the chimney chase so technicians can see the attic floor, framing bays, roof deck, and penetrations. They look for open top plates, missing blocking, gaps around flues, scorched materials, moisture staining, rodent debris, and failed sealant. Exposing these areas prevents fire-stopping materials from being installed over concealed defects.
Low roof slopes, tight framing, deep insulation, and limited attic entry can restrict access to the chase perimeter. Access conditions determine whether technicians can install continuous blocking, sheet metal, mineral wool, or sealant around the full opening. If the chase cannot be safely reached or the flue condition remains unclear, the work scope must be revised before installation.
03
Our technicians install noncombustible blocking, mineral wool, sheet metal, and compatible high-temperature sealants at approved chase openings and air leakage paths. They maintain clearance around the chimney, protect wiring from heat exposure, and avoid using combustible foam or ordinary caulk where the location requires fire-rated or noncombustible materials.
The goal is to close the air path while preserving the chimney’s required operating space.
Existing framing and chimney components determine the installation method. Richmond Hill Attic Insulation & Air Sealing repairs unstable blocking, removes unsuitable debris, and seals accessible joints before restoring insulation. Missing listed components or damage to a factory-built chimney can stop the work until the correct part or professional assessment is available.
04
After fire-stopping, technicians reposition or replace attic insulation around the chase without placing material against restricted chimney surfaces. They check the continuity of blocking, the integrity of sealant, the position of collars, the condition of framing, and the clearance between insulation and flue components. This stage matters because displaced insulation can reopen the air path or create a new heat-exposure concern.
Richmond Hill Attic Insulation & Air Sealing reviews the completed chase for exposed gaps, loose material, water entry, damaged insulation, and accessible service points. Remaining chimney defects, roof leaks, or clearance concerns are documented instead of concealed beneath insulation. The final recommendation reflects the condition of both the attic boundary and the chimney assembly.
Yes, chimney chase air sealing can be safe around a metal chimney when the chimney type, listed clearances, support components, and required fire-stop locations are identified first. Richmond Hill Attic Insulation & Air Sealing inspects the flue, support box, collars, framing, insulation, and chase opening before selecting noncombustible materials. Damaged chimney parts, missing listed components, or uncertain clearances require correction or review before sealing.
Chimney chase fire-stopping may use mineral wool, sheet metal, noncombustible blocking, high-temperature sealant, and compatible listed fire-stop components. Our technicians select materials according to the chimney assembly, opening size, heat exposure, framing condition, and manufacturer requirements where applicable. Richmond Hill Attic Insulation & Air Sealing does not use ordinary combustible materials in locations that require noncombustible separation.
No, chimney chase air sealing cannot repair every roof leak because water entry may originate at flashing, counterflashing, masonry joints, the chimney cap, or the roof covering. Our technicians look for moisture staining, wet insulation, damaged sheathing, deteriorated mortar, and visible flashing defects while inspecting the attic-side chase. Air sealing can proceed only after active water entry is corrected or separated from the attic repair scope.
No, attic insulation should not touch a chimney chase where the chimney assembly requires clearance or noncombustible separation. Richmond Hill Attic Insulation & Air Sealing checks the flue type, framing, insulation movement, discoloration, scorching, and existing fire-stopping before repositioning material. Insulation is restored only in areas permitted by the chimney configuration, while overheating or smoke damage requires a broader safety evaluation.
Warning signs include visible gaps around the flue, missing blocking, insulation touching a hot chimney, scorched wood, brittle sealant, soot, smoke odor, attic drafts, moisture stains, and debris inside the chase. Our technicians inspect the full accessible perimeter and distinguish fire-stopping deficiencies from chimney or roof defects. Richmond Hill Attic Insulation & Air Sealing then defines whether the next step is sealing, noncombustible blocking, insulation correction, chimney repair, or referral for specialized evaluation.